The world of powder milling comes with a plethora of terminology that includes the material itself, how it's measured, the forces used to change it, and the equipment that processes it.
Some terms are also defined by how a measurement is produced. For example, a D50 reported using one particle sizing method or a D90 - what do these really mean?
Simple terms such as “mesh” and “fine grinding” can quickly become misinterpreted, which is why we’ve put together this glossary, grouping together the terms most commonly encountered in this industry, with handy, short definitions that can be easily referenced.
For more information on specific terms, visit Quadro’s comprehensive range of guides that covers many of the topics in this piece in greater depth.
This glossary can be used however you see fit. It can be used to look up a term right at the moment a definition is needed or scanned, topic-to-topic, to get a better understanding of the words used within it.
The terms in the glossary have been grouped by function:
The definitions cover what the terms mean without turning each entry into a complex technical guide.
We’ve also been careful to ensure parts of a term have been defined. Knowing what screen blinding means becomes easier to understand once terms such as “Screen” and "Aperture" have been explained.
Powder particle sizes are often defined by a distribution, rather than a single universal diameter. This is because a batch of powder will contain particles of many sizes, they won’t all be the exact same size. Instead, a range is agreed upon that is acceptable for the wider process to go ahead successfully.
Particle size distribution (PSD): The spread of particle sizes in a sample. PSD does not refer to a single particle diameter but encompasses the size and frequency of several within a group.
D10, D50, and D90: Percentile sizes taken from a cumulative distribution. D10 is the size at or below which 10% of the measured material lies, D50 means 50% of particles are smaller and acts as the median, whereas D90 defines that 90% of particles are smaller than the stated size point. For example:
10% of particles are below 15 µm
Half are below 45 µm
90% are below 120 µm
Span: One way of describing the width of a distribution that is calculated for a volume distribution as (D90-D10)/D50. A value that is lower tends to indicate that the 10th and 90th percentile points sit closer together and are termed as having a narrow PSD. Whereas a figure above 2.5 is deemed to have a broad distribution.
Micrometer (µm or micron): One millionth of a meter. Typically, “Micron” is the most widely used term although “Micrometer” remains the more formal option. By way of example, flour ranges from 50-150µm and sugar is 500-1000µm.
Mesh: refers to the screen openings. It describes the number of apertures that are found per linear inch and is therefore a description of the screen’s construction. So a 20 mesh has 20 openings per inch, 100 mesh has 100 openings, as the number increases the hole size reduces. Micron to Mesh conversions are often given in tables, and are useful to see if the particle size will pass through the opening, but the PSD can still range from a few microns up to the maximum particle size that will pass through.
Here, you’ll find several words that are likely familiar and which describe overlapping processes. Other terms in this section are used to define processes which use force to cause particles to break apart.
Comminution: The reduction of particle sizes via a fracturing method. This is a broad technical term for intensive particle-size reduction.
Milling and grinding: Both are umbrella terms for mechanical size reduction, and their precise use varies between industries. A useful distinction often relates to the required final particle sizes and the mechanism involved in achieving that. Grinding is achieved using ball mills, jet or pin mills or hammer mills where the objective is to make the particles smaller, such as grinding powdered sugar. Whereas milling is a term relating to an entire operation that can also encapsulate not only particle size reduction, but also deagglomeration, homogenization and particle shape modification.
Fine grinding: A process that is used to achieve substantially smaller particle sizes compared to conventional coarse sizing or delumping. Fine grinding is a distinct processing category alongside conical milling and screening/deagglomeration. It is commonly used in pharmaceutical processes to increase drug dissolution rates or improve bioavailability or for inhalation powders.
Micronization: Size reduction in the extreme. Particles are reduced down to the 10µm. Jet milling is one way to achieve this level of particle size reduction. Used to improve the bioavailability of poorly soluble drug compounds.
Impact: Particle breakage caused by a high-speed collision with another particle, element, or moving surface. Typically delivered by Hammer mills or pin & jet mills. Ideal for brittle materials.
Shear: A reduction in size that is produced when material moves across a surface and causes it to fracture or cut. Shearing is often used to describe the action between an impeller and screen in a conical mill process.
Compression: Breakages that are caused by squeezing materials between opposing surfaces or forces. This is achieved using roller mills or high pressure rolls.
Attrition: Here, reduction is caused by particles rubbing or colliding with other particles or surfaces. In powder handling, attrition is used to describe unwanted particle degradation that produces fines.
There are key distinctions that separate deliberate fractures from processes intended mainly to condition or separate an existing powder population.
Agglomerate: a group of smaller particles bonded strongly enough that they act as one larger particle. The original particles have not changed in size, they are just adhering to each other. They typically show up as lumps in the powder ingredients, having been caused by storage conditions, humidity, pressure during transport or electrostatic attraction.
Deagglomeration/delumping: This process breaks clusters or lumps apart without grinding the component particles themselves. That distinction matters in cases where the process’ objective is to restore flow or remove material that has accumulated during storage or drying. Quadro’s FlexSift, for instance, combines security screening with gentle deagglomeration, which breaks down agglomerated material while ensuring oversize foreign material is retained.
Reclaim: Reconditioning out of spec material so that usable product can be returned to the process rather than being rejected.
Sieving: Separating particles into size classes by using a defined sieve or aperture. Sieving is commonly used for particle-size analysis.
Screening: This is the corresponding manufacturing operation to sieving in which a screen separates or conditions a material.
Security screening: Screening is used to prevent unwanted oversize material or foreign matter from continuing downstream of the process. The Quadro FlexSift can be used for security screening and deagglomeration.
Granulation: Bringing smaller particles together into larger agglomerates or granules.
Wet granulation: Granule formation achieved using a liquid or binder-containing wet mass which is then dried and conditioned to certain requirements.
Dry granulation: Granule formation that is done without adding a liquid via compaction followed by sizing.
Granule calibration: A type of conditioning that forms granules into more consistent sizes before the next stage. At this point, milling is intended to control granule dimensions, not to simply grind a powder down to the smallest possible size.
Here, we’ll define the machines and their components that many in the powder milling sector will encounter when moving from a process requirement to selecting equipment.
Cone mill/conical mill: A screen mill in which material enters into a conical milling chamber and is rotated by an impeller before passing through openings in a surrounding screen.
Comil®: Quadro’s name for its conical mill screen that was developed back in 1976. Current Comil configurations use a combination of screens, impellers, and speeds to achieve a required PSD.
Conical screen: The holed component through which material can exit the milling chamber once it has reached the appropriate size. The size of the apertures and their geometry can influence the cone mill process.
Impeller: The rotating tooling which moves product around the milling zone.
Screen-impeller gap: The clearance and working relationship between these two components. A change in the gap can alter the relationship, which means the gap itself is a process variable rather than a mechanical clearance.
Jet mill: This process uses high-velocity gas and particle collisions for fine or micron-scale size reduction. It is widely used in pharmaceutical settings.
Pin mill: Uses high-speed rotating pins to apply impact and mechanical forces to the material that's been fed into it.
Hammer mill: Hammers or beaters break material through repeated impact.
Ball or media mill: Primarily uses a grinding motion to create impact.
Here are terms that describe what happens during operation as well as the quality or safety framework around the process itself.
Fines: Particles that are smaller than the intended size. A “Fine” will be defined differently depending on the process rather than there being one agreed definition of it.
Yield: The amount of material recovered as a usable on-specification product after processing.
Throughput: The quantity of material a mill or screening system processes over a defined period.
Residence time: The length of time material remains within the processing zone, often the milling chamber. Longer residence times expose particles to additional attrition, which can affect PSD goals and fines generation.
Flood feeding: The supply of material continuously so the mill starts working on the product without precisely metered feeding.
Screen blinding: The accumulation of particles on a screen’s surface until the apertures become restricted or blocked.
cGMP: Stands for Current Good Manufacturing Practice. In US pharmaceutical regulation, cGMP describes systems and controls intended to assure processes and facilities remain compliant and produce products of required identity, strength, and quality.
ATEX: The name for the European directives concerned with explosive atmospheres. In Great Britain, workplace requirements derived from the ATEX Workplace Directive are implemented through The Dangerous Substances and Explosive Atmospheres Regulations 2002 (DSEAR). Dust from powder milling can create an explosive atmosphere that must be assessed and controlled.
Containment: Measures used to prevent powder escaping the processing system, especially in instances where dust, contamination, or occupational exposure must be controlled.
Occupational Exposure Band (OEB): This is a categorization that is used to group substances by occupational exposure or containment requirement. The band definitions and exposure ranges should always be checked against the system being used.
Useful milling specifications start with language because terms that appear interchangeable can lead to different processing decisions being made.
Delumping is not the same requirement as fine grinding in the same way D50 does not describe the whole PSD, and a mesh number is not an independent particle-size measurement.
Quadro can help translate the required PSD and product requirement into an appropriate powder milling configuration.